Home / Products / Comet Cable Glands / Comet Weatherproof Type Double Compression Cable Gland
Comet Weatherproof Type Double Compression Cable Gland ( Armoured Cables)
Indoor Or Outdoor Gland For Single Wire Armoured Cables |
|||||||
Gland reference |
Cable dimensions |
Gland dimensions |
|||||
| Diameter | Armour wire diameter |
Entry thread | Across flats (E) |
Across corners (F) |
|||
| Under armour (A) |
Overall Diameter (B) |
Entry (C) |
Length (D) |
||||
| size | mm | mm | mm | inch | mm | mm | mm |
| CBW01SS | 8.0 | 12.0 | 0.8/1.4 | 3/4" | 15.0 | 21.0 | 24.5 |
| CBW01S | 11.0 | 16.5 | 0.8/1.4 | 3/4" | 15.0 | 25.0 | 29.0 |
| CBW01 | 12.0 | 18.0 | 0.8/1.4 | 3/4" | 15.0 | 28.0 | 32.0 |
| CBW01A | 12.0 | 18.0 | 0.8/1.4 | 1" | 15.0 | 28.0 | 32.0 |
| CBW02 | 14.0 | 20.0 | 0.8/1.4 | 1" | 15.0 | 31.5 | 36.5 |
| CBW02A | 14.0 | 20.0 | 0.8/1.4 | 3/4" | 15.0 | 31.5 | 36.5 |
| CBW03 | 17.0 | 23.0 | 0.8/1.4 | 1" | 15.0 | 32.0 | 37.0 |
| CBW04 | 20.0 | 26.0 | 0.8/1.4 | 1" | 15.0 | 38.0 | 44.0 |
| CBW04A | 20.0 | 26.0 | 0.8/1.4 | 1.1/4" | 15.0 | 38.0 | 44.0 |
| CBW05 | 24.0 | 30.0 | 0.8/1.4 | 1.1/4" | 15.0 | 41.0 | 47.0 |
| CBW05A | 24.0 | 30.0 | 0.8/1.4 | 1.1/2" | 15.0 | 41.0 | 47.0 |
| CBW06 | 27.0 | 33.0 | 0.8/1.4 | 1.1/2" | 15.0 | 47.0 | 54.0 |
| CBW06A | 27.0 | 33.0 | 0.8/1.4 | 1.1/4" | 15.0 | 47.0 | 54.0 |
| CBW07 | 30.0 | 37.0 | 0.8/1.4 | 1.1/2" | 15.0 | 52.0 | 58.0 |
| CBW08 | 35.0 | 41.0 | 0.8/1.4 | 2" | 15.0 | 56.0 | 64.0 |
| CBW09 | 40.0 | 46.0 | 0.8/1.4 | 2" | 15.0 | 59.0 | 67.0 |
| CBW010 | 46.0 | 52.0 | 0.8/1.4 | 2" | 20.0 | 66.5 | 77.0 |
| CBW010A | 46.0 | 52.0 | 0.8/1.4 | 2.1/2" | 20.0 | 66.5 | 77.0 |
| CBW011S | 50.0 | 56.0 | 0.8/1.4 | 2.1/2" | 20.0 | 74.0 | 85.0 |
| CBW011 | 54.0 | 60.0 | 0.8/1.4 | 2.1/2" | 20.0 | 80.0 | 92.0 |
| CBW012 | 60.0 | 66.0 | 0.8/1.4 | 3" | 20.0 | 85.0 | 97.0 |
| CBW013A | 66.0 | 72.0 | 0.8/1.4 | 3" | 20.0 | 90.0 | 103.0 |
| CBW013 | 72.0 | 78.0 | 0.8/1.4 | 3.1/4" | 20.0 | 99.0 | 113.0 |
| CBW014 | 78.0 | 84.0 | 0.8/1.4 | 3.1/2" | 20.0 | 105.0 | 122.0 |
| CBW015 | 88.0 | 94.0 | 0.8/1.4 | 4" | 20.0 | 117.0 | 135.0 |
| CBW016 | 98.0 | 105.0 | 0.8/1.4 | 41/2" | 20.0 | 130.0 | 149.0 |
Application :
For use under most climatic conditions.This are Weatherproof as per IP66-IS 13947 part I and may be used in the corrosive conditions when protected by the shroud.
Specification :
Gland consist of locknut 1, washer 2, armour clamping nut 3, neoprene inner ring 4, armour clamping cone 5, amour clamping ring 6, gland body 7, neoprene outer ring 8, skid washer 9, outer seal nut 10. All metal parts are made of brass accurately machined for ease of assembly.
Accessories :
Shrouds and Earth tags are supplied separately and should be specified when ordering the gland.
Materials & Finishes :
M.O.C :
a. Cable Gland is manufactured in Brass (standard).
b. Alternate material - Stainless Steel / Aluminium.
Sealing Ring : Neoprene Rubber
Thread :
a. Glands are supplied with B.S.C. thread (ET) as standard.
b. Alternate thread forms available are - NPT / PG / BSP / MM etc.
Finish :
a. Nickel Plated (standard)
b. Alternate Plating - Tin / Cadmium / Chrome
Protection Class : IP 60 as per IS 13947 Part I
Ref Standard : BS 6121 : 2005 (BS EN 50262)
Fiting Sequence
a) Screw item 2 into apparatus (secure with item 1 if plain hole entry.)
b) Pass item 10,9,8,7 respectively over cable before commencing to strip oversheath.
c) Remove the over sheath and pass item 6 over exposed armour.
d) Cut armour to length, lift wire ends, pass item 5 over exposed bedding and beneath armour.
e) Pass item 4.
f) Pass cable end through item 3.
g) Engage item 7 and 3 and tighten up.
h) Engage item 10 and 7 and tighten up.
i) Screw item 3,2 into apparatus (secure with item 1 if plain hole entry.)
Comet Weatherproof Type Double Compression Cable Gland ( Un-Armoured Cables)
Indoor Or Outdoor Gland For Single Wire Armoured Cables |
|||||||
Gland reference |
Cable dimensions |
Gland dimensions |
|||||
| Diameter | Entry thread | Across flats (E) |
Across corners (F) |
||||
| Under armour (A) |
Overall Diameter (B) |
Entry (C) |
Length (D) |
||||
| size | mm | mm | inch | mm | mm | mm | |
| CBW01SS (UN) | 13.0 | 13.0 | 3/4" | 15.0 | 21.5 | 24.5 | |
| CBW01S (UN) | 14.0 | 14.5 | 3/4" | 15.0 | 25.0 | 29.0 | |
| CBW01A (UN) | 18.0 | 18.0 | 1" | 15.0 | 28.0 | 32.0 | |
| CBW02 (UN) | 20.0 | 20.0 | 1" | 15.0 | 31.5 | 36.5 | |
| CBW03SP (UN) | 23.0 | 23.0 | M28 | 15.0 | 32.0 | 37.0 | |
| CBW04A (UN) | 26.0 | 26.0 | 1.1/4" | 15.0 | 38.0 | 44.0 | |
| CBW05A (UN) | 30.0 | 30.0 | 1.1/2" | 15.0 | 41.0 | 47.0 | |
| CBW06SP (UN) | 33.0 | 33.0 | M40 | 15.0 | 47.0 | 54.0 | |
| CBW07SP (UN) | 36.0 | 36.0 | M42 | 15.0 | 52.0 | 58.0 | |
| CBW08 (UN) | 41.0 | 41.0 | 2" | 15.0 | 56.0 | 64.0 | |
| CBW09 (UN) | 44.0 | 44.0 | 2" | 15.0 | 59.0 | 67.0 | |
| CBW010A (UN) | 52.0 | 52.0 | 2" | 20.0 | 66.5 | 77.0 | |
| CBW011SP (UN) | 60.0 | 60.0 | M70 | 20.0 | 80.0 | 92.0 | |
| CBW012 (UN) | 66.0 | 66.0 | 3" | 20.0 | 85.0 | 97.0 | |
| CBW013 (UN) | 72.0 | 72.0 | 3.1/4" | 20.0 | 90.0 | 103.0 | |
| CBW014 (UN) | 80.0 | 80.0 | 3.1/2" | 20.0 | 105.0 | 122.0 | |
| CBW015 (UN) | 90.0 | 90.0 | 4" | 20.0 | 117.0 | 135.0 | |
Application :
For use under most climatic conditions & generally for un-armored cables & outdoor use. This are Weatherproof and may be used in the corrosive conditions when protected by the shroud.
Specification :
Gland consist of locknut 1, washer 2, armour clamping nut 3, neoprene inner ring 4, gland body 5, neoprene outer ring 6, skid washer 7, outer seal nut 8. All metal parts are made of brass accurately machined for ease of assembly.
Accessories :
Shrouds and Earth tags are supplied separately and should be specified when ordering the gland.
Materials & Finishes :
M.O.C :
a. Cable Gland is manufactured in Brass (standard).
b. Alternate material - Stainless Steel / Aluminium.
Sealing Ring : Neoprene Rubber
Thread :
a. Glands are supplied with B.S.C. thread (ET) as standard.
b. Alternate thread forms available are - NPT / PG / BSP / MM etc.
Finish :
a. Nickel Plated (standard)
b. Alternate Plating - Tin / Cadmium / Chrome
Protection Class : IP 55 as per IS 13947 Part I
Ref Standard : BS 6121 : 2005 (BS EN 50262)
Fiting Sequence
a) Pass item 8,7,6,5,4 & 3 respectively over cable.
b) Engage item 5 and 3 and tighten up.
c) Engage item 8 and 5 and tighten up.
d) Screw item 3,2 into apparatus (secure with item 1 if plain hole entry.)